Double side planer manufacturer and supplier by v-holdmachinery.com
Double planer machine supplier 2023: Planers are usually identified by the width and thickness of the wood they will plane. A 12 inch model is great for most home workshop jobs, but bigger ones would be required for professional environments. Never force the work-piece into the thicknesser or planner as the machine has a feed control that adjusts the speed at which the wood passes the cutter head. What is a Pressing Machine, And How Does it Work? Pressing machines are also known as forming presses. A machine press is a tool used in the manufacturing industry to deform/shape a work-piece under high pressure. There are different types of machine presses, including cabinet presses, frame presses, solid surface presses, composite presses, multi-daylight presses, cold presses, rubber presses, recycling presses and much more. Read even more information on double surface planer.
The radial arm saw is pretty much a portable circular saw that glides on an adjustable arm suspended over a fixed cutting surface. The blade and motor are connected to the arm by a yoke, which is adjustable along both horizontal and vertical planes, enabling the saw to be swung in a variety of directions. For cross-cut work, position the board flush with the fence at the rear of the saw and draw the blade across the wood. The bevel lock allows the saw to be tilted for cutting angles. You can set it to the desired angle using the protractor on the saw housing. The saw can be swivelled right or left for mitring, or turned a full 90 degrees for ripping. The blade can also be raised or lowered using a crank. The size of the saw is determined by the dimension of the blade the saw can accommodate. As an example a model using a 10 inch blade would be able to cut work-pieces up to 3 inches thick.
Up-acting machines typically apply hydraulic pressure from the centre of the lower beam which pushes the lower beam upwards into a fixed upper beam. Tonnage is applied to the centre of the lower beam in an upward fashion. The flex in the bend tends to be even from left to right. Hydraulics are used to push the lower beam up and gravity is used to return the lower beam down. A loss in power will result in the brake being in the open position. Since the lower beam does move during operation, feedback to the operator is given. Knowing the lower beam is moving can be a safety feature. Down-acting machines are preferred if staged bending is important. Staged bending is a valuable option that can significantly improve productivity while minimising setup time.
A mortise is a square slot cut in the direction of depth for the purpose of making a mortise and tenon joint in a wooden piece. The mortising woodworking machines are used for cutting mortise and tenon joints which are very laborious and time consuming operations. There are three types of mortisers, namely (1) hollow chisel mortiser (2) chain mortiser and (3) oscillating bit mortiser. The hollow chisel mortiser, the most commonly used woodworking machines, consists of a revolving spindle carrying an auger bit at the bottom end. The auger bit rotates at a high speed inside a hollow chisel of square section. When the chisel is forced into the wood, the bit bores a square hole by the sharp end of the chisel, the auger bit and chisel thus work together and perform boring of a square hole. The depth of the mortise is regulated by means of an adjustable depth stop. The spindle is rotated by an electric motor, and tool-feed is obtained by pressing foot-lever.
The next woodworking machines are band saws. The band saw is designed to cut wood by means of an endless metal saw band that travels over the rims of two or more rotating wheels. Other parts of a band saw are frame, table, saw guides, saw tensioning arrangement, etc. Although the number of operation that can be performed on a band saw is less than those of a circular saw, it is most useful for making curved or irregular cuts in wood.
The wood is fixed between the headstock and tailstock of the lathe. The headstock houses the motor that spins the work-piece. The tailstock is adjustable, moving along the length of the bed to fit work-pieces of various lengths. Once the work-piece is locked in place, the tool rest is set into position. The spinning work-piece is then shaped using a chisel or gouge held fast to the tool rest. Face-plate turning, in with the work-piece is fastened with screws to the face plate of the drive spindle, allows the woodworker to produce bowls and other hollow goods. See even more details at https://www.v-holdmachinery.com/.
Founded in 1996, V-HOLD have more than 20 years of professional four-sided plane production, to create China’s four-sided plane first brand and commits itself to provide the most secure, reliable, efficient, energy-saving, economical production equipment for the customers around the world. Nowadays, most of the products including 4-Side Moulder, Multiple Rip Saw, Multiple Rip Saw with Double Side Planner, and Automotive Floor Production Line have passed ISO9001: 2000 quality system.
