Some advices for paintless dent repair tasks
Customize my ride: For dents that are fairly small and not deep, a dent repair kit may be an inexpensive and simple solution. These kits are available at any auto parts store and tend to be very user friendly — instructions are always included. The best part is that they usually cost under $40. Most include several stems for various sized dents, a glue gun and a knockdown tool. You may be surprised at how well the kit works and how professional the result looks. We don’t recommend this kit for large, deep dents — you might cause even more damage trying to fix those with a kit.
1st let’s begin with some car paint care tricks: If you can not expose your car to the sunlight, you can use a hair dryer instead. Just aim the hair dryer to the areas you want to fix, and wait until the dents even out. The ideal distance between the hair dryer and the car should be 2-4 inches. While using a hair dryer, there should be an interval of 2 minutes. If the car’s paint starts discoloring, you should stop applying heat right away. Use a rubbing compound or wax to revise the paint color.
Don’t underestimate the necessary step of decontamination prior to application of your chosen wax. If you fail to do this step, you will get disappointing results regardless of the type of wax you have chosen. And yes…even that brand new car straight off the dealer lot will in have some form of pollutants already on the car paint from its travel from the factory to the car dealership. Clear coat is the top layer of your cars paint. It acts as a protective layer to filter out UV rays. But your clear coat is what you are trying to take care of with the above requirements. People get confused about clear coat vs. car paint. Virtually every car today is finished with a clear coat as the top layer. Think of it as car paint with no color added to it.
Not only can you unclog a drain with a plunger, but you can also get out small- to medium-sized dents out of your car too. Just splash some water on both the plunger and the dent and start pushing and pulling until it pops out. Make sure to use a cup plunger (for sinks), not a flange one (for toilets). Reversing into an object is one of the easiest ways to get a dent. So for plastic bumpers, even if you attempt to take off the bumper, it might still be difficult to push out the dent because of how stiff the plastic is. Solve this issue by boiling some water in a pot and throwing it on the dent.
Undercoating: Although waxing the car and polishing it produces good results, you need to protect the car from long term damage by undercoating and rust-proofing it. When the car metal is oxidized, rust sets in and destroys the surface of the car. To avoid this, you should consider rust-proofing the vehicle, particularly if you reside in a state where the humidity is high. Find additional information at Auto Decals & Lettering Colorado Springs.
If you are interested in learning how to do paintless dent repair, make sure that you take the time to gather the right tools and supplies, learn about the detailed process of PDR, and then spend time practicing your own repair techniques on metal panels from the local junk yard before you start doing repairs on your own vehicles.
So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.
