Top welding tips

Here are some advices about welding supplies and how to make the best purchase picks. Flat-Position Welding Increases Welding Speed : It’s common knowledge that welding in a horizontal position will be the easiest and fastest way to weld. A flat position is not as taxing to maintain and the welding puddle will stay in place. Take some time to evaluate each project before beginning in order to make sure the majority of welds can be completed in this position. If a job calls for vertical welding, see this article about vertical welding. Core Wire Feeder Increases TIG Welding Speed: For professional welders hoping to speed up TIG welding, a core wire feeder will add filler metal through an automated process. Watch this video on how it works. This enables welders to work with both hands and to maintain a constant flow of wire into the welding puddle. Ed Craig at the Frabricator writes about the wire feeder process first developed in Europe, saying it is “suitable for all-position welding on materials of any thickness, the process addresses traditional GTAW limitations and can enhance both manual and automated TIG weld quality and productivity.”

TIG Welding / Gas Tungsten Arc Welding (GTAW) — TIG welding is an arc welding process that uses a non-consumable tungsten electrode to produce the weld. The weld area is protected from atmospheric contamination by a shielding gas (usually argon) and a filler metal, though some welds, known as autogenous welds, do not require it. A constant-current welding power supply produces energy that is conducted across the arc through a column of highly ionized gas and metal vapors known as plasma. TIG welding is most commonly used to weld thin sections of alloy steel, stainless steel and nonferrous metals such as aluminum, magnesium and copper alloys. The process grants the operator greater control over the weld than other welding processes, allowing for strong, high-quality welds. TIG welding is comparatively more complex and difficult to master than other processes and is significantly slower.

In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode. Looking for the best TIG Welders? We recommend Welding Supplies Direct & associated company TWS Direct Ltd is an online distributor of a wide variety of welding supplies, welding equipment and welding machine. We supply plasma cutters, MIG, TIG, ARC welding machines and support consumables to the UK, Europe and North America.

Don’t use too much torch gas when welding aluminum on A/C. Don’t use too much torch gas when welding aluminum on A/C. Aluminum takes a lot of amperage to weld. Even though the melting temperature of aluminum is less than half that for steel, it takes about twice as much amperage to weld. Why? Because aluminum conducts heat away from the weld puddle faster than you can put it in. this brings me to an important point. Do not use more argon than necessary on your torch gas. If you do, it will be like blowing cool air on something you are trying to heat up with a torch. All that argon blowing on the part makes for a loud erratic arc because the arc force is so great. Have you ever lit up on a thick aluminum casting and listened to how loud the arc is? I bet your torch gas was up around 20 like the books recommend. That’s too much for aluminum (unless you are using an argon helium mix).

Best welding advices: how to become a better welder and how to choose the best welding equipment. 2% thoriated tungsten electrodes are mildly radioactive: Word on the street is that 2% thoriated tungsten electrodes are mildly radioactive. They say deer meat is too. No one gets out alive. Good news though…and it’s not just that I saved a bundle on my car insurance by switching to GEICO.. I have learned through testing a bunch of arc starts and by welding on all different metals that 2% lanthanated electrodes are about as good as the 2% thoriated. I even like the lanthanated a little better for some applications. So if you are scared of thoriated tungsten but you are even more scared of crappy electrodes that don’t work as well, use 2% lanthanated…they are colored blue. One word to the wise here. The blue ones are not brittle like 2% thoriated electrodes. And they splinter if you try to break them or snip with dykes. You have to cut or score with a grinder in order to cut to size or cut off a bib blob of metal you don’t want to sand off.

Never forget that welding, when done improperly, can be hazardous. Electric shock, fumes and gases, arc rays, hot parts, noise and a host of other possible hazards come along with the territory. The ultraviolet and infrared light rays can also burn your skin — similar to a sunburn but without the subsequent tan — and your eyes. This is why the best MIG welding operator knows how to stay safe.

First, practice handling the gun without actually welding. Rest its barrel in one hand, and support that hand on the table. The other hand operates the gun’s trigger. Stand in a comfortable position and move the gun steadily over the work surface. Adjust your posture and gun movement so that they feel natural. Attach the work lead to the workpiece, and hold the gun so the wire meets the weld surface at about a 30-degree angle. Touch the wire very lightly to the surface, squeeze the trigger, and gently pull the gun toward you to make your first test weld. The wire should melt off into the weld puddle at an even rate and make a steady crackling noise as you go. Adjust the welder settings if needed. Source: https://www.weldingsuppliesdirect.co.uk/.